AimSizer, i Am Sizer Solutions

ISO 60 Plastics Apparent Density Tester︱Bulk Density Tester

LABULK 305 Apparent Density Tester and Bulk Density Meter is an apparatus measures physically the apparent density of plastic materials and moulding materials. LABULK 305 is produced strictly according to international standard ISO 60 bulk density Plastics - Determination of Apparent Density of Material that can be poured from a specified funnel and the tested values is equivalent to ASTM D 1895 Standard Test Method for Apparent Density, Bulk Factor, and Pourability of Plastic Materials-Test Method A. Test Method A and ISO Method R 60 have been found to give values that differ by - 0.01 to + 0.03 apparent density units (g/cm3) based on the average of five tests for each of three materials.

SEND INQUIRY

You can make an inquiry about this product.
Your e-mail will not be leaked.

  • PRODUCT DETAIL
  • SPECIFICATIONS&APPARATUS
  • PRINCIPLE
  • DEMO VIDEO
  • APPARENT DENSITY

LABULK 305 Plastics Apparent Density Tester and Bulk Density Tester

hall flow meter – fisher sub-sieve sizer

LABULK 305 Apparent Density Tester and Bulk Density Meter is an apparatus measures physically the apparent density of plastic materials and moulding materials. LABULK 305 is produced strictly according to international standard ISO 60 bulk density Plastics – Determination of Apparent Density of Material that can be poured from a specified funnel and the tested values is equivalent to ASTM D 1895 Standard Test Method for Apparent Density, Bulk Factor, and Pourability of Plastic Materials-Test Method A. Test Method A and ISO Method R 60 have been found to give values that differ by – 0.01 to + 0.03 apparent density units (g/cm3) based on the average of five tests for each of three materials.

HMK-22 Fisher Sub-sieve sizer Sub sieve sizer Average particle size analysis Supplier Price Manual

AS-300 Hall Flowmeter︱Flow Meter Funnel︱Metal Powder Flow Rate︱Apparent Density︱Carney︱Manufacturer

labulk-305-plastics-apparent-density-tester-and-bulk-density-meter-new-design

labulk-305-plastics-apparent-density-tester-and-bulk-density-meter-new-design

labulk-305-plastics-apparent-density-tester-and-bulk-density-meter-old design

labulk-305-plastics-apparent-density-tester-and-bulk-density-meter-old design

LABULK 307 Plastics Moulding Materials Apparent Density Tester︱Funnel︱ASTM D1895 A

LABULK 308 Apparent Density Tester︱Plastics Moulding Materials Measurement︱ASTM D1895 Method B

SPECIFICATIONS&APPARATUS

  • Funnel, as per ISO 60 funnel
  • Measuring cylinder, Capacity 100ml, internal dia. 45 mm
  • Stand & Support
  • Straightedge
  • Calibration certificate (optional)
  • Calculation software & report (optional)
  • Scale, accurate to 0,1 g (optional)

PRINCIPLE

LABULK 305 Apparent Density Tester is designed according to ISO 60 international standard which specifies a method of determining the apparent density, that is the mass per unit of volume, of loose material (powder or granular material) that can be poured from a funnel of specified design.

DEMO VIDEO

http://youtu.be/pFul118V4eE

APPARENT DENSITY

Manufacturer

AimSizer is a world leading manufacturer of Bulk Density Testers, all the apparent density testers are designed and manufactured according to international standards on cost-effective basis.

Frequently Asked Questions

Which ISO standard applys when determining the apparent density of loose moulding material that can not be poured from a specified funnel?
-ISO 61 Plastics - Determination of apparent density of moulding material that cannot be poured from a specified funnel.

What is the scope of ISO 60 Plastics - Determination of apparent density of material that can be poured from a specified funnel?
-This international standard specifies a method of determining the apparent density, i.e. the mass per unit of volume, of loose material (powder or granular material) that can be poured from a funnel of specified design.

Name of ISO 60 about plastics,moulding materials,tests,physical tests,density measurement and bulk density?
-International Standard ISO 60 is Platics-Determination of apparent density of material that can be poured froma specified funnel.

Customize

In case user has his particular requirements please feel free to let us know and we will quote reasonable price.